When the program was running before hibernation the green light goes off while the computer
goes to sleep ánd is back up when the computer was wake. The cam was 'off' while the computer
was in hibernation mode.

"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:ezQXoGZmIHA.4196@TK2MSFTNGP04.phx.gbl...
> Does the cam remain "on" though the hibernation period?
>
> Steve Miller wrote:
>
>> The cam was not actually new hardware after hibernation. All the other usb devices are
>> ok after hibernation and to function correct with no failure. Only the cam does not.
>>
>> The motherboard was from around '04, and I did install all the latest drivers but now do
>> have the one installed Windows XP picked. All the same.
>>
>> Steve
>>
>> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmIHA.6032@TK2MSFTNGP03.phx.gbl...
>>
>>>In hibernation the PC shuts off, and does not look for "new" things when powered back on. Perhaps "find new hardware" will
>>>restore the cam after hibernation.
>>>
>>>Steve Miller wrote:
>>>
>>>>Bob I, I think the hub was powered. I could plug the usb drive in the cams hub, it will work.
>>>>
>>>>I even could unplug the cam prior to starting the LifeCam program and plug it back into the
>>>>same hub the program still off, the cam will work.
>>>>
>>>>It also works fine with a freshly booted up computer and after standby also. Only after
>>>>hibernation it does not.
>>>>
>>>>Steve
>>>>
>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA.1912@TK2MSFTNGP04.phx.gbl...
>>>>
>>>>
>>>>>Perhaps plug it into a powered hub?
>>>>>
>>>>>Steve Miller wrote:
>>>>>
>>>>>
>>>>>
>>>>>>Hi Bob I!
>>>>>>
>>>>>>Thank you for your reply. I did, but didn't help at all. Sorry I forgot to mention.
>>>>>>
>>>>>>Steve
>>>>>>
>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
>>>>>>
>>>>>>
>>>>>>
>>>>>>>Go into Device Manager and in the Universal Serial Serial Bus section, go through the hubs,r-click on them, open
>>>>>>>"Properties", then on the Power Management tab, UNcheck "Allow the computer to turn off this device........"
>>>>>>>
>>>>>>>Steve Miller wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>>Hello!
>>>>>>>>
>>>>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
>>>>>>>>sent to hibernation and came back from it.
>>>>>>>>
>>>>>>>>I have got other devices sticking in other usb hubs that function with no problems (usb flash
>>>>>>>>drive, a keyboard, external hard drive ).
>>>>>>>>
>>>>>>>>When the cam was up and running prior to hibernation or while hibernation :-), everything will
>>>>>>>>be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
>>>>>>>>no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>>>>>>>>hibernation with no prior preparation the cams image(s ) will not show up, but a black square
>>>>>>>>only and the green light on top of the cam does not flash
>>>>>>>>
>>>>>>>>Was any one used to the problem and can help?
>>>>>>>>
>>>>>>>>Thank you,
>>>>>>>>Steve
>>>>>>>
>>>>
>>
>>
>

Try plugging directly into the PC, or contact MS tech support, or
replace the camera.

Steve Miller wrote:

> That's a good idea since the cam was working already. :-) What else could I try out?
>
> I still hope that there was some setting I'm not used to now that wouldfix the issue.
>
> Steve
>
> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:u6$FJsZmIHA.1280@TK2MSFTNGP05.phx.gbl...
> If the green light is on after the PC is back up, try "find new hardware".
>
> Steve Miller wrote:
>
>>When the program was running before hibernation the green light goes off while the computer
>>goes to sleep ánd is back up when the computer was wake. The cam was 'off' while the computer
>>was in hibernation mode.
>>
>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:ezQXoGZmIHA.4196@TK2MSFTNGP04.phx.gbl...
>>
>>
>>>Does the cam remain "on" though the hibernation period?
>>>
>>>Steve Miller wrote:
>>>
>>>
>>>
>>>>The cam was not actually new hardware after hibernation. All the other usb devices are
>>>>ok after hibernation and to function correct with no failure. Only the cam does not.
>>>>
>>>>The motherboard was from around '04, and I did install all the latestdrivers but now do
>>>>have the one installed Windows XP picked. All the same.
>>>>
>>>>Steve
>>>>
>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmIHA.6032@TK2MSFTNGP03.phx.gbl...
>>>>
>>>>
>>>>
>>>>>In hibernation the PC shuts off, and does not look for "new" things when powered back on. Perhaps "find new hardware" will
>>>>>restore the cam after hibernation.
>>>>>
>>>>>Steve Miller wrote:
>>>>>
>>>>>
>>>>>
>>>>>>Bob I, I think the hub was powered. I could plug the usb drive in the cams hub, it will work.
>>>>>>
>>>>>>I even could unplug the cam prior to starting the LifeCam program and plug it back into the
>>>>>>same hub the program still off, the cam will work.
>>>>>>
>>>>>>It also works fine with a freshly booted up computer and after standby also. Only after
>>>>>>hibernation it does not.
>>>>>>
>>>>>>Steve
>>>>>>
>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA.1912@TK2MSFTNGP04.phx.gbl...
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>>Perhaps plug it into a powered hub?
>>>>>>>
>>>>>>>Steve Miller wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>>Hi Bob I!
>>>>>>>>
>>>>>>>>Thank you for your reply. I did, but didn't help at all. Sorry I forgot to mention.
>>>>>>>>
>>>>>>>>Steve
>>>>>>>>
>>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>>Go into Device Manager and in the Universal Serial Serial Bus section, go through the hubs,r-click on them, open
>>>>>>>>>"Properties", then on the Power Management tab, UNcheck "Allow the computer to turn off this device........"
>>>>>>>>>
>>>>>>>>>Steve Miller wrote:
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>>Hello!
>>>>>>>>>>
>>>>>>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
>>>>>>>>>>sent to hibernation and came back from it.
>>>>>>>>>>
>>>>>>>>>>I have got other devices sticking in other usb hubs that function with no problems (usb flash
>>>>>>>>>>drive, a keyboard, external hard drive ).
>>>>>>>>>>
>>>>>>>>>>When the cam was up and running prior to hibernation or while hibernation :-), everything will
>>>>>>>>>>be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
>>>>>>>>>>no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>>>>>>>>>>hibernation with no prior preparation the cams image(s ) will not show up, but a black square
>>>>>>>>>>only and the green light on top of the cam does not flash
>>>>>>>>>>
>>>>>>>>>>Was any one used to the problem and can help?
>>>>>>>>>>
>>>>>>>>>>Thank you,
>>>>>>>>>>Steve
>>>>>>>>>
>>
>
>

Do you think it could be something with the chip set or there like?

"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:uudzi9ZmIHA.5368@TK2MSFTNGP04.phx.gbl...
Try plugging directly into the PC, or contact MS tech support, or
replace the camera.

Steve Miller wrote:

> That's a good idea since the cam was working already. :-) What else could I try out?
>
> I still hope that there was some setting I'm not used to now that would fix the issue.
>
> Steve
>
> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:u6$FJsZmIHA.1280@TK2MSFTNGP05.phx.gbl...
> If the green light is on after the PC is back up, try "find new hardware".
>
> Steve Miller wrote:
>
>>When the program was running before hibernation the green light goes off while the computer
>>goes to sleep ánd is back up when the computer was wake. The cam was 'off' while the computer
>>was in hibernation mode.
>>
>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:ezQXoGZmIHA.4196@TK2MSFTNGP04.phx.gbl...
>>
>>
>>>Does the cam remain "on" though the hibernation period?
>>>
>>>Steve Miller wrote:
>>>
>>>
>>>
>>>>The cam was not actually new hardware after hibernation. All the other usb devices are
>>>>ok after hibernation and to function correct with no failure. Only the cam does not.
>>>>
>>>>The motherboard was from around '04, and I did install all the latest drivers but now do
>>>>have the one installed Windows XP picked. All the same.
>>>>
>>>>Steve
>>>>
>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmIHA.6032@TK2MSFTNGP03.phx.gbl...
>>>>
>>>>
>>>>
>>>>>In hibernation the PC shuts off, and does not look for "new" things when powered back on. Perhaps "find new hardware" will
>>>>>restore the cam after hibernation.
>>>>>
>>>>>Steve Miller wrote:
>>>>>
>>>>>
>>>>>
>>>>>>Bob I, I think the hub was powered. I could plug the usb drive in the cams hub, it will work.
>>>>>>
>>>>>>I even could unplug the cam prior to starting the LifeCam program and plug it back into the
>>>>>>same hub the program still off, the cam will work.
>>>>>>
>>>>>>It also works fine with a freshly booted up computer and after standby also. Only after
>>>>>>hibernation it does not.
>>>>>>
>>>>>>Steve
>>>>>>
>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA.1912@TK2MSFTNGP04.phx.gbl...
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>>Perhaps plug it into a powered hub?
>>>>>>>
>>>>>>>Steve Miller wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>>Hi Bob I!
>>>>>>>>
>>>>>>>>Thank you for your reply. I did, but didn't help at all. Sorry I forgot to mention.
>>>>>>>>
>>>>>>>>Steve
>>>>>>>>
>>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>>Go into Device Manager and in the Universal Serial Serial Bus section, go through the hubs,r-click on them, open
>>>>>>>>>"Properties", then on the Power Management tab, UNcheck "Allow the computer to turn off this device........"
>>>>>>>>>
>>>>>>>>>Steve Miller wrote:
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>>Hello!
>>>>>>>>>>
>>>>>>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
>>>>>>>>>>sent to hibernation and came back from it.
>>>>>>>>>>
>>>>>>>>>>I have got other devices sticking in other usb hubs that function with no problems (usb flash
>>>>>>>>>>drive, a keyboard, external hard drive ).
>>>>>>>>>>
>>>>>>>>>>When the cam was up and running prior to hibernation or while hibernation :-), everything will
>>>>>>>>>>be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
>>>>>>>>>>no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>>>>>>>>>>hibernation with no prior preparation the cams image(s ) will not show up, but a black square
>>>>>>>>>>only and the green light on top of the cam does not flash
>>>>>>>>>>
>>>>>>>>>>Was any one used to the problem and can help?
>>>>>>>>>>
>>>>>>>>>>Thank you,
>>>>>>>>>>Steve
>>>>>>>>>
>>
>
>

Given that everything else comes back ok, I would hesitate to condemn
the chipset/motherboard.

Steve Miller wrote:
> Do you think it could be something with the chip set or there like?
>
> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:uudzi9ZmIHA.5368@TK2MSFTNGP04.phx.gbl...
> Try plugging directly into the PC, or contact MS tech support, or
> replace the camera.
>
> Steve Miller wrote:
>
>
>>That's a good idea since the cam was working already. :-) What else could I try out?
>>
>>I still hope that there was some setting I'm not used to now that wouldfix the issue.
>>
>>Steve
>>
>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:u6$FJsZmIHA.1280@TK2MSFTNGP05.phx.gbl...
>>If the green light is on after the PC is back up, try "find new hardware".
>>
>>Steve Miller wrote:
>>
>>
>>>When the program was running before hibernation the green light goes off while the computer
>>>goes to sleep ánd is back up when the computer was wake. The cam was'off' while the computer
>>>was in hibernation mode.
>>>
>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:ezQXoGZmIHA.4196@TK2MSFTNGP04.phx.gbl...
>>>
>>>
>>>
>>>>Does the cam remain "on" though the hibernation period?
>>>>
>>>>Steve Miller wrote:
>>>>
>>>>
>>>>
>>>>
>>>>>The cam was not actually new hardware after hibernation. All the other usb devices are
>>>>>ok after hibernation and to function correct with no failure. Only the cam does not.
>>>>>
>>>>>The motherboard was from around '04, and I did install all the latest drivers but now do
>>>>>have the one installed Windows XP picked. All the same.
>>>>>
>>>>>Steve
>>>>>
>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmIHA.6032@TK2MSFTNGP03.phx.gbl...
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>>In hibernation the PC shuts off, and does not look for "new" thingswhen powered back on. Perhaps "find new hardware" will
>>>>>>restore the cam after hibernation.
>>>>>>
>>>>>>Steve Miller wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>>Bob I, I think the hub was powered. I could plug the usb drive in the cams hub, it will work.
>>>>>>>
>>>>>>>I even could unplug the cam prior to starting the LifeCam program and plug it back into the
>>>>>>>same hub the program still off, the cam will work.
>>>>>>>
>>>>>>>It also works fine with a freshly booted up computer and after standby also. Only after
>>>>>>>hibernation it does not.
>>>>>>>
>>>>>>>Steve
>>>>>>>
>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA.1912@TK2MSFTNGP04.phx.gbl...
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>>Perhaps plug it into a powered hub?
>>>>>>>>
>>>>>>>>Steve Miller wrote:
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>>Hi Bob I!
>>>>>>>>>
>>>>>>>>>Thank you for your reply. I did, but didn't help at all. Sorry Iforgot to mention.
>>>>>>>>>
>>>>>>>>>Steve
>>>>>>>>>
>>>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>>Go into Device Manager and in the Universal Serial Serial Bus section, go through the hubs,r-click on them, open
>>>>>>>>>>"Properties", then on the Power Management tab, UNcheck "Allow the computer to turn off this device........"
>>>>>>>>>>
>>>>>>>>>>Steve Miller wrote:
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>>Hello!
>>>>>>>>>>>
>>>>>>>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
>>>>>>>>>>>sent to hibernation and came back from it.
>>>>>>>>>>>
>>>>>>>>>>>I have got other devices sticking in other usb hubs that function with no problems (usb flash
>>>>>>>>>>>drive, a keyboard, external hard drive ).
>>>>>>>>>>>
>>>>>>>>>>>When the cam was up and running prior to hibernation or while hibernation :-), everything will
>>>>>>>>>>>be fine. Also, what I can do was to un-plug and to re-plug thecam to the same hub. That's but
>>>>>>>>>>>no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>>>>>>>>>>>hibernation with no prior preparation the cams image(s ) will not show up, but a black square
>>>>>>>>>>>only and the green light on top of the cam does not flash
>>>>>>>>>>>
>>>>>>>>>>>Was any one used to the problem and can help?
>>>>>>>>>>>
>>>>>>>>>>>Thank you,
>>>>>>>>>>>Steve
>>>>>>>>>>
>>
>
>

I have had an other cam prior, which did not work either. It had a faulty joint that
couldn't keep the lens upright. Tthat's why I think it's something with the computer
sooner than with the cam.

"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OA0FzbamIHA.1368@TK2MSFTNGP02.phx.gbl...
Given that everything else comes back ok, I would hesitate to condemn
the chipset/motherboard.

Steve Miller wrote:
> Do you think it could be something with the chip set or there like?
>
> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:uudzi9ZmIHA.5368@TK2MSFTNGP04.phx.gbl...
> Try plugging directly into the PC, or contact MS tech support, or
> replace the camera.
>
> Steve Miller wrote:
>
>
>>That's a good idea since the cam was working already. :-) What else could I try out?
>>
>>I still hope that there was some setting I'm not used to now that would fix the issue.
>>
>>Steve
>>
>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:u6$FJsZmIHA.1280@TK2MSFTNGP05.phx.gbl...
>>If the green light is on after the PC is back up, try "find new hardware".
>>
>>Steve Miller wrote:
>>
>>
>>>When the program was running before hibernation the green light goes off while the computer
>>>goes to sleep ánd is back up when the computer was wake. The cam was 'off' while the computer
>>>was in hibernation mode.
>>>
>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:ezQXoGZmIHA.4196@TK2MSFTNGP04.phx.gbl...
>>>
>>>
>>>
>>>>Does the cam remain "on" though the hibernation period?
>>>>
>>>>Steve Miller wrote:
>>>>
>>>>
>>>>
>>>>
>>>>>The cam was not actually new hardware after hibernation. All the other usb devices are
>>>>>ok after hibernation and to function correct with no failure. Only the cam does not.
>>>>>
>>>>>The motherboard was from around '04, and I did install all the latest drivers but now do
>>>>>have the one installed Windows XP picked. All the same.
>>>>>
>>>>>Steve
>>>>>
>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmIHA.6032@TK2MSFTNGP03.phx.gbl...
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>>In hibernation the PC shuts off, and does not look for "new" things when powered back on. Perhaps "find new hardware" will
>>>>>>restore the cam after hibernation.
>>>>>>
>>>>>>Steve Miller wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>>Bob I, I think the hub was powered. I could plug the usb drive in the cams hub, it will work.
>>>>>>>
>>>>>>>I even could unplug the cam prior to starting the LifeCam program and plug it back into the
>>>>>>>same hub the program still off, the cam will work.
>>>>>>>
>>>>>>>It also works fine with a freshly booted up computer and after standby also. Only after
>>>>>>>hibernation it does not.
>>>>>>>
>>>>>>>Steve
>>>>>>>
>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA.1912@TK2MSFTNGP04.phx.gbl...
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>>Perhaps plug it into a powered hub?
>>>>>>>>
>>>>>>>>Steve Miller wrote:
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>>Hi Bob I!
>>>>>>>>>
>>>>>>>>>Thank you for your reply. I did, but didn't help at all. Sorry I forgot to mention.
>>>>>>>>>
>>>>>>>>>Steve
>>>>>>>>>
>>>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>>Go into Device Manager and in the Universal Serial Serial Bus section, go through the hubs,r-click on them, open
>>>>>>>>>>"Properties", then on the Power Management tab, UNcheck "Allow the computer to turn off this device........"
>>>>>>>>>>
>>>>>>>>>>Steve Miller wrote:
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>>Hello!
>>>>>>>>>>>
>>>>>>>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
>>>>>>>>>>>sent to hibernation and came back from it.
>>>>>>>>>>>
>>>>>>>>>>>I have got other devices sticking in other usb hubs that function with no problems (usb flash
>>>>>>>>>>>drive, a keyboard, external hard drive ).
>>>>>>>>>>>
>>>>>>>>>>>When the cam was up and running prior to hibernation or while hibernation :-), everything will
>>>>>>>>>>>be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
>>>>>>>>>>>no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>>>>>>>>>>>hibernation with no prior preparation the cams image(s ) will not show up, but a black square
>>>>>>>>>>>only and the green light on top of the cam does not flash
>>>>>>>>>>>
>>>>>>>>>>>Was any one used to the problem and can help?
>>>>>>>>>>>
>>>>>>>>>>>Thank you,
>>>>>>>>>>>Steve
>>>>>>>>>>
>>
>
>

Try it on some other computer?

Steve Miller wrote:

> I have had an other cam prior, which did not work either. It had a faulty joint that
> couldn't keep the lens upright. Tthat's why I think it's something withthe computer
> sooner than with the cam.
>
> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OA0FzbamIHA.1368@TK2MSFTNGP02.phx.gbl...
> Given that everything else comes back ok, I would hesitate to condemn
> the chipset/motherboard.
>
> Steve Miller wrote:
>
>>Do you think it could be something with the chip set or there like?
>>
>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:uudzi9ZmIHA.5368@TK2MSFTNGP04.phx.gbl...
>>Try plugging directly into the PC, or contact MS tech support, or
>>replace the camera.
>>
>>Steve Miller wrote:
>>
>>
>>
>>>That's a good idea since the cam was working already. :-) What else could I try out?
>>>
>>>I still hope that there was some setting I'm not used to now that would fix the issue.
>>>
>>>Steve
>>>
>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:u6$FJsZmIHA.1280@TK2MSFTNGP05.phx.gbl...
>>>If the green light is on after the PC is back up, try "find new hardware".
>>>
>>>Steve Miller wrote:
>>>
>>>
>>>
>>>>When the program was running before hibernation the green light goes off while the computer
>>>>goes to sleep ánd is back up when the computer was wake. The cam was 'off' while the computer
>>>>was in hibernation mode.
>>>>
>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:ezQXoGZmIHA.4196@TK2MSFTNGP04.phx.gbl...
>>>>
>>>>
>>>>
>>>>
>>>>>Does the cam remain "on" though the hibernation period?
>>>>>
>>>>>Steve Miller wrote:
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>>The cam was not actually new hardware after hibernation. All the other usb devices are
>>>>>>ok after hibernation and to function correct with no failure. Only the cam does not.
>>>>>>
>>>>>>The motherboard was from around '04, and I did install all the latest drivers but now do
>>>>>>have the one installed Windows XP picked. All the same.
>>>>>>
>>>>>>Steve
>>>>>>
>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmIHA.6032@TK2MSFTNGP03.phx.gbl...
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>>In hibernation the PC shuts off, and does not look for "new" things when powered back on. Perhaps "find new hardware" will
>>>>>>>restore the cam after hibernation.
>>>>>>>
>>>>>>>Steve Miller wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>>Bob I, I think the hub was powered. I could plug the usb drive inthe cams hub, it will work.
>>>>>>>>
>>>>>>>>I even could unplug the cam prior to starting the LifeCam programand plug it back into the
>>>>>>>>same hub the program still off, the cam will work.
>>>>>>>>
>>>>>>>>It also works fine with a freshly booted up computer and after standby also. Only after
>>>>>>>>hibernation it does not.
>>>>>>>>
>>>>>>>>Steve
>>>>>>>>
>>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA.1912@TK2MSFTNGP04.phx.gbl...
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>>Perhaps plug it into a powered hub?
>>>>>>>>>
>>>>>>>>>Steve Miller wrote:
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>>Hi Bob I!
>>>>>>>>>>
>>>>>>>>>>Thank you for your reply. I did, but didn't help at all. Sorry I forgot to mention.
>>>>>>>>>>
>>>>>>>>>>Steve
>>>>>>>>>>
>>>>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>>Go into Device Manager and in the Universal Serial Serial Bus section, go through the hubs,r-click on them, open
>>>>>>>>>>>"Properties", then on the Power Management tab, UNcheck "Allowthe computer to turn off this device........"
>>>>>>>>>>>
>>>>>>>>>>>Steve Miller wrote:
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>>Hello!
>>>>>>>>>>>>
>>>>>>>>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies notwork after the computer was
>>>>>>>>>>>>sent to hibernation and came back from it.
>>>>>>>>>>>>
>>>>>>>>>>>>I have got other devices sticking in other usb hubs that function with no problems (usb flash
>>>>>>>>>>>>drive, a keyboard, external hard drive ).
>>>>>>>>>>>>
>>>>>>>>>>>>When the cam was up and running prior to hibernation or whilehibernation :-), everything will
>>>>>>>>>>>>be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
>>>>>>>>>>>>no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>>>>>>>>>>>>hibernation with no prior preparation the cams image(s ) willnot show up, but a black square
>>>>>>>>>>>>only and the green light on top of the cam does not flash
>>>>>>>>>>>>
>>>>>>>>>>>>Was any one used to the problem and can help?
>>>>>>>>>>>>
>>>>>>>>>>>>Thank you,
>>>>>>>>>>>>Steve
>>>>>>>>>>>
>>
>
>

That's a good idea. May I come over?

"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eQHS36amIHA.2396@TK2MSFTNGP02.phx.gbl...
Try it on some other computer?

Steve Miller wrote:

> I have had an other cam prior, which did not work either. It had a faulty joint that
> couldn't keep the lens upright. Tthat's why I think it's something with the computer
> sooner than with the cam.
>
> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OA0FzbamIHA.1368@TK2MSFTNGP02.phx.gbl...
> Given that everything else comes back ok, I would hesitate to condemn
> the chipset/motherboard.
>
> Steve Miller wrote:
>
>>Do you think it could be something with the chip set or there like?
>>
>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:uudzi9ZmIHA.5368@TK2MSFTNGP04.phx.gbl...
>>Try plugging directly into the PC, or contact MS tech support, or
>>replace the camera.
>>
>>Steve Miller wrote:
>>
>>
>>
>>>That's a good idea since the cam was working already. :-) What else could I try out?
>>>
>>>I still hope that there was some setting I'm not used to now that would fix the issue.
>>>
>>>Steve
>>>
>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:u6$FJsZmIHA.1280@TK2MSFTNGP05.phx.gbl...
>>>If the green light is on after the PC is back up, try "find new hardware".
>>>
>>>Steve Miller wrote:
>>>
>>>
>>>
>>>>When the program was running before hibernation the green light goes off while the computer
>>>>goes to sleep ánd is back up when the computer was wake. The cam was 'off' while the computer
>>>>was in hibernation mode.
>>>>
>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:ezQXoGZmIHA.4196@TK2MSFTNGP04.phx.gbl...
>>>>
>>>>
>>>>
>>>>
>>>>>Does the cam remain "on" though the hibernation period?
>>>>>
>>>>>Steve Miller wrote:
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>>The cam was not actually new hardware after hibernation. All the other usb devices are
>>>>>>ok after hibernation and to function correct with no failure. Only the cam does not.
>>>>>>
>>>>>>The motherboard was from around '04, and I did install all the latest drivers but now do
>>>>>>have the one installed Windows XP picked. All the same.
>>>>>>
>>>>>>Steve
>>>>>>
>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmIHA.6032@TK2MSFTNGP03.phx.gbl...
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>>In hibernation the PC shuts off, and does not look for "new" things when powered back on. Perhaps "find new hardware" will
>>>>>>>restore the cam after hibernation.
>>>>>>>
>>>>>>>Steve Miller wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>>Bob I, I think the hub was powered. I could plug the usb drive in the cams hub, it will work.
>>>>>>>>
>>>>>>>>I even could unplug the cam prior to starting the LifeCam program and plug it back into the
>>>>>>>>same hub the program still off, the cam will work.
>>>>>>>>
>>>>>>>>It also works fine with a freshly booted up computer and after standby also. Only after
>>>>>>>>hibernation it does not.
>>>>>>>>
>>>>>>>>Steve
>>>>>>>>
>>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA.1912@TK2MSFTNGP04.phx.gbl...
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>>Perhaps plug it into a powered hub?
>>>>>>>>>
>>>>>>>>>Steve Miller wrote:
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>>Hi Bob I!
>>>>>>>>>>
>>>>>>>>>>Thank you for your reply. I did, but didn't help at all. Sorry I forgot to mention.
>>>>>>>>>>
>>>>>>>>>>Steve
>>>>>>>>>>
>>>>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>>Go into Device Manager and in the Universal Serial Serial Bus section, go through the hubs,r-click on them, open
>>>>>>>>>>>"Properties", then on the Power Management tab, UNcheck "Allow the computer to turn off this device........"
>>>>>>>>>>>
>>>>>>>>>>>Steve Miller wrote:
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>>Hello!
>>>>>>>>>>>>
>>>>>>>>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
>>>>>>>>>>>>sent to hibernation and came back from it.
>>>>>>>>>>>>
>>>>>>>>>>>>I have got other devices sticking in other usb hubs that function with no problems (usb flash
>>>>>>>>>>>>drive, a keyboard, external hard drive ).
>>>>>>>>>>>>
>>>>>>>>>>>>When the cam was up and running prior to hibernation or while hibernation :-), everything will
>>>>>>>>>>>>be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
>>>>>>>>>>>>no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>>>>>>>>>>>>hibernation with no prior preparation the cams image(s ) will not show up, but a black square
>>>>>>>>>>>>only and the green light on top of the cam does not flash
>>>>>>>>>>>>
>>>>>>>>>>>>Was any one used to the problem and can help?
>>>>>>>>>>>>
>>>>>>>>>>>>Thank you,
>>>>>>>>>>>>Steve
>>>>>>>>>>>
>>
>
>

I'm pretty sure you know someone local with a computer.

Steve Miller wrote:

> That's a good idea. May I come over?
>
> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eQHS36amIHA.2396@TK2MSFTNGP02.phx.gbl...
> Try it on some other computer?
>
> Steve Miller wrote:
>
>
>>I have had an other cam prior, which did not work either. It had a faulty joint that
>>couldn't keep the lens upright. Tthat's why I think it's something withthe computer
>>sooner than with the cam.
>>
>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OA0FzbamIHA.1368@TK2MSFTNGP02.phx.gbl...
>>Given that everything else comes back ok, I would hesitate to condemn
>>the chipset/motherboard.
>>
>>Steve Miller wrote:
>>
>>
>>>Do you think it could be something with the chip set or there like?
>>>
>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:uudzi9ZmIHA.5368@TK2MSFTNGP04.phx.gbl...
>>>Try plugging directly into the PC, or contact MS tech support, or
>>>replace the camera.
>>>
>>>Steve Miller wrote:
>>>
>>>
>>>
>>>
>>>>That's a good idea since the cam was working already. :-) What else could I try out?
>>>>
>>>>I still hope that there was some setting I'm not used to now that would fix the issue.
>>>>
>>>>Steve
>>>>
>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:u6$FJsZmIHA.1280@TK2MSFTNGP05.phx.gbl...
>>>>If the green light is on after the PC is back up, try "find new hardware".
>>>>
>>>>Steve Miller wrote:
>>>>
>>>>
>>>>
>>>>
>>>>>When the program was running before hibernation the green light goesoff while the computer
>>>>>goes to sleep ánd is back up when the computer was wake. The cam was 'off' while the computer
>>>>>was in hibernation mode.
>>>>>
>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:ezQXoGZmIHA.4196@TK2MSFTNGP04.phx.gbl...
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>>Does the cam remain "on" though the hibernation period?
>>>>>>
>>>>>>Steve Miller wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>>The cam was not actually new hardware after hibernation. All the other usb devices are
>>>>>>>ok after hibernation and to function correct with no failure. Onlythe cam does not.
>>>>>>>
>>>>>>>The motherboard was from around '04, and I did install all the latest drivers but now do
>>>>>>>have the one installed Windows XP picked. All the same.
>>>>>>>
>>>>>>>Steve
>>>>>>>
>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmIHA.6032@TK2MSFTNGP03.phx.gbl...
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>>In hibernation the PC shuts off, and does not look for "new" things when powered back on. Perhaps "find new hardware" will
>>>>>>>>restore the cam after hibernation.
>>>>>>>>
>>>>>>>>Steve Miller wrote:
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>>Bob I, I think the hub was powered. I could plug the usb drive in the cams hub, it will work.
>>>>>>>>>
>>>>>>>>>I even could unplug the cam prior to starting the LifeCam program and plug it back into the
>>>>>>>>>same hub the program still off, the cam will work.
>>>>>>>>>
>>>>>>>>>It also works fine with a freshly booted up computer and after standby also. Only after
>>>>>>>>>hibernation it does not.
>>>>>>>>>
>>>>>>>>>Steve
>>>>>>>>>
>>>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA.1912@TK2MSFTNGP04.phx.gbl...
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>>Perhaps plug it into a powered hub?
>>>>>>>>>>
>>>>>>>>>>Steve Miller wrote:
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>>Hi Bob I!
>>>>>>>>>>>
>>>>>>>>>>>Thank you for your reply. I did, but didn't help at all. SorryI forgot to mention.
>>>>>>>>>>>
>>>>>>>>>>>Steve
>>>>>>>>>>>
>>>>>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>>Go into Device Manager and in the Universal Serial Serial Bussection, go through the hubs,r-click on them, open
>>>>>>>>>>>>"Properties", then on the Power Management tab, UNcheck "Allow the computer to turn off this device........"
>>>>>>>>>>>>
>>>>>>>>>>>>Steve Miller wrote:
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>>Hello!
>>>>>>>>>>>>>
>>>>>>>>>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
>>>>>>>>>>>>>sent to hibernation and came back from it.
>>>>>>>>>>>>>
>>>>>>>>>>>>>I have got other devices sticking in other usb hubs that function with no problems (usb flash
>>>>>>>>>>>>>drive, a keyboard, external hard drive ).
>>>>>>>>>>>>>
>>>>>>>>>>>>>When the cam was up and running prior to hibernation or while hibernation :-), everything will
>>>>>>>>>>>>>be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
>>>>>>>>>>>>>no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>>>>>>>>>>>>>hibernation with no prior preparation the cams image(s ) will not show up, but a black square
>>>>>>>>>>>>>only and the green light on top of the cam does not flash
>>>>>>>>>>>>>
>>>>>>>>>>>>>Was any one used to the problem and can help?
>>>>>>>>>>>>>
>>>>>>>>>>>>>Thank you,
>>>>>>>>>>>>>Steve
>>>>>>>>>>>>
>>
>
>

Not at the time being to be honest.

"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23EkU0gbmIHA.536@TK2MSFTNGP06.phx.gbl...
I'm pretty sure you know someone local with a computer.

Steve Miller wrote:

> That's a good idea. May I come over?
>
> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eQHS36amIHA.2396@TK2MSFTNGP02.phx.gbl...
> Try it on some other computer?
>
> Steve Miller wrote:
>
>
>>I have had an other cam prior, which did not work either. It had a faulty joint that
>>couldn't keep the lens upright. Tthat's why I think it's something with the computer
>>sooner than with the cam.
>>
>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OA0FzbamIHA.1368@TK2MSFTNGP02.phx.gbl...
>>Given that everything else comes back ok, I would hesitate to condemn
>>the chipset/motherboard.
>>
>>Steve Miller wrote:
>>
>>
>>>Do you think it could be something with the chip set or there like?
>>>
>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:uudzi9ZmIHA.5368@TK2MSFTNGP04.phx.gbl...
>>>Try plugging directly into the PC, or contact MS tech support, or
>>>replace the camera.
>>>
>>>Steve Miller wrote:
>>>
>>>
>>>
>>>
>>>>That's a good idea since the cam was working already. :-) What else could I try out?
>>>>
>>>>I still hope that there was some setting I'm not used to now that would fix the issue.
>>>>
>>>>Steve
>>>>
>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:u6$FJsZmIHA.1280@TK2MSFTNGP05.phx.gbl...
>>>>If the green light is on after the PC is back up, try "find new hardware".
>>>>
>>>>Steve Miller wrote:
>>>>
>>>>
>>>>
>>>>
>>>>>When the program was running before hibernation the green light goes off while the computer
>>>>>goes to sleep ánd is back up when the computer was wake. The cam was 'off' while the computer
>>>>>was in hibernation mode.
>>>>>
>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:ezQXoGZmIHA.4196@TK2MSFTNGP04.phx.gbl...
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>>Does the cam remain "on" though the hibernation period?
>>>>>>
>>>>>>Steve Miller wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>>The cam was not actually new hardware after hibernation. All the other usb devices are
>>>>>>>ok after hibernation and to function correct with no failure. Only the cam does not.
>>>>>>>
>>>>>>>The motherboard was from around '04, and I did install all the latest drivers but now do
>>>>>>>have the one installed Windows XP picked. All the same.
>>>>>>>
>>>>>>>Steve
>>>>>>>
>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmIHA.6032@TK2MSFTNGP03.phx.gbl...
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>>In hibernation the PC shuts off, and does not look for "new" things when powered back on. Perhaps "find new hardware" will
>>>>>>>>restore the cam after hibernation.
>>>>>>>>
>>>>>>>>Steve Miller wrote:
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>>Bob I, I think the hub was powered. I could plug the usb drive in the cams hub, it will work.
>>>>>>>>>
>>>>>>>>>I even could unplug the cam prior to starting the LifeCam program and plug it back into the
>>>>>>>>>same hub the program still off, the cam will work.
>>>>>>>>>
>>>>>>>>>It also works fine with a freshly booted up computer and after standby also. Only after
>>>>>>>>>hibernation it does not.
>>>>>>>>>
>>>>>>>>>Steve
>>>>>>>>>
>>>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA.1912@TK2MSFTNGP04.phx.gbl...
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>>Perhaps plug it into a powered hub?
>>>>>>>>>>
>>>>>>>>>>Steve Miller wrote:
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>>Hi Bob I!
>>>>>>>>>>>
>>>>>>>>>>>Thank you for your reply. I did, but didn't help at all. Sorry I forgot to mention.
>>>>>>>>>>>
>>>>>>>>>>>Steve
>>>>>>>>>>>
>>>>>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>>Go into Device Manager and in the Universal Serial Serial Bus section, go through the hubs,r-click on them, open
>>>>>>>>>>>>"Properties", then on the Power Management tab, UNcheck "Allow the computer to turn off this device........"
>>>>>>>>>>>>
>>>>>>>>>>>>Steve Miller wrote:
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>>Hello!
>>>>>>>>>>>>>
>>>>>>>>>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
>>>>>>>>>>>>>sent to hibernation and came back from it.
>>>>>>>>>>>>>
>>>>>>>>>>>>>I have got other devices sticking in other usb hubs that function with no problems (usb flash
>>>>>>>>>>>>>drive, a keyboard, external hard drive ).
>>>>>>>>>>>>>
>>>>>>>>>>>>>When the cam was up and running prior to hibernation or while hibernation :-), everything will
>>>>>>>>>>>>>be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
>>>>>>>>>>>>>no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>>>>>>>>>>>>>hibernation with no prior preparation the cams image(s ) will not show up, but a black square
>>>>>>>>>>>>>only and the green light on top of the cam does not flash
>>>>>>>>>>>>>
>>>>>>>>>>>>>Was any one used to the problem and can help?
>>>>>>>>>>>>>
>>>>>>>>>>>>>Thank you,
>>>>>>>>>>>>>Steve
>>>>>>>>>>>>
>>
>
>